[Feb-2026] HPE7-A06 Pre-Exam Practice Tests Exam Questions and Answers for Aruba Certified Professional – Campus Access Study Guide [Q38-Q54]

NEW QUESTION 38
An IT administrator wants to set up an HPE Aruba Networking User Experience Insight (UXI) sensor. During the initiation process, the administrator sees that the color of the LED is orange.
What does the orange LED mean?

The sensor needs multi-rate port but this port is only standard 1G port

The sensor is still booting

The sensor cannot connect to the UXI cloud

This is a G6E UXI sensor and does not have enough PoE power

NEW QUESTION 39
What is the best practice for using Dynamic Segmentation?

Use UBT to create isolated networks for specific types of devices.

Use a combination of role-based access and overlay technologies to create a layered security approach

Use LUR to assign roles to devices based on their location and DUR to assign roles to devices based on their user identity.

Use Dynamic Segmentation only on devices that are connected to the network via Wi-Fi.

NEW QUESTION 40
A customer is experiencing problems with BGP on their AOS-CX network. The users cannot access specific resources on the network, even though they have been assigned the appropriate roles and permissions.
What is the most likely cause of the problem?

The HPE Aruba Networking ClearPass configuration is incorrect.

The GBP tags are not being applied correctly to the user’s traffic.

The GBP database is corrupted.

The users are not being assigned the correct GBP classes.

NEW QUESTION 41
Refer to the exhibit.

IGMP v3 was enabled on both VSX switches. Which switch becomes the IGMP querier for clients connected to Acc-1 switch?

Agg-2

both Agg-1 and Agg-2

Agg-1

Active gateway IP will be used as IGMP querier.

NEW QUESTION 42
In an HPE network, which scenarios can indicate a configuration issue with Link Aggregation (LACP)?

Unstable link state

Increased latency on traffic paths

Port flapping

Spanning tree topology changes

NEW QUESTION 43
A senior engineer from the network operations team has reported an intermittent problem where some PoE- powered devices are randomly losing power. During your investigation, you found that port 1 of the Acc-1 switch is currently presenting the behavior shown in the CLI output for the Acc-1.

What is a probablecausa lot poor 1/1/1 is denying PoE?

This switch does no! support PoE class 4.

switch PoE powerbudget exceeded

PoE port priority sot to low

PoE was manually disabled for port 1/1/1.

NEW QUESTION 44
You have recently configured a switch for 802.1X authentication with HPE Aruba Networking ClearPass. A security admin is seeing events with the following description in ClearPass Event Viewer.
‘RADIUS authentication attempt from unknown NAD (10.10.1.10:1812)’
Which command should you use to identify the configuration issue?

show ip source-interface radius

show aaa authentication-server radius

show radius-server shared-secret

show radius-server detail

NEW QUESTION 45
A user cannot connect to the wired network using 802.1X with EAP-TLS. The user’s device is configured correctly and the user has a valid certificate. The RADIUS server logs show that the user is authenticating successfully.
What could be the reason for this issue?

There is an issue with the switch interface configuration.

The user’s device is not using the correct certificate authority.

The switch is not configured to use EAP-TLS.

The RADIUS server is not configured to use EAP-TLS.

NEW QUESTION 46
The customer is experiencing periodic uplink congestion between campus-1’s AGG-1 and core. This has boon negativelyaffecting voice communications.The VOIP phones edge mark their packets with DSCP EF. The uplink from AGG-1 to core is LAG1.
The customer has already configured the following class and policy on AGG-1:

Based on this policy, which scrip), when deployed on AGG-1. will improve the reliable forwarding of voice trafficbetween AGG-1 and its uplink to the core?

NEW QUESTION 47
A client would like to use the HPE Aruba Networking Switch MultiEdit Software function in HPE Aruba Networking Central.
Which option is available?

Use CLI scripts and apply them to selected switches.

Run the same NAE scripts for selected switches.

Use templates and apply them to selected switches.

Apply a configuration to an interface range for selected switches.

NEW QUESTION 48
Exhibit.

A conference venue has a requirement to secure independent network users from each other in their network.
The following configurations are created on Edge-1:

change the VLAN 152 private-vlan community

change the VLAN 151 private-vlan community

change the VLAN 152 type. primary-vlan 152

change the VLAN 151 primary-vlan 151

The requirement is to secure independent network users from each other in a conference venue using Edge-1.
This scenario typically calls for Private VLANs,specifically using the ‘isolated’ type to prevent communication between hosts within the same secondary VLAN.
* Analysis of Options:
* Private VLANs consist of a primary VLAN and one or more secondary VLANs (isolated or community). Isolated ports cannot communicate with other isolated ports in the same VLAN; they can only communicate with promiscuous ports (usually the router uplink). Community ports can communicate with each other and promiscuous ports.
* Option A: Configures VLAN 152 as private-vlan community.
* Option B: Configures VLAN 151 as private-vlan community.
* Option C: Defines VLAN 152 as a primary-vlan associated with itself, which isn’t standard syntax
/logic.
* Option D: Defines VLAN 151 as a primary-vlan associated with itself.
* The goal isisolation. None of the options directly configure an isolated VLAN. Options A and B configure community VLANs, which allow communication between users within that VLAN, contradicting the requirement. Options C and D attempt to define primary VLANs in a potentially incorrect way.
* Caveat:There seems to be an issue with the provided options. Standard configuration to make VLAN 151 isolated would involve defining a primary VLAN (e.g., vlan 152 private-vlan primary) and then defining VLAN 151 as isolated (vlan 151 private-vlan isolated). Since none of the options correctly configure anisolatedVLAN, and the requirement is isolation, the question or options are likely flawed. However, if forced to interpret intent, questions sometimes test understanding of thetypesof private VLANs. Changing a VLANtocommunity type (Option B for VLAN 151) is a distinct action, even if it doesn’t meet the statedisolationgoal. Without correct options for ‘isolated’, selecting the ‘best’ flawed option is difficult. Assuming the question intends to configure VLAN 151 assome typeof private secondary VLAN, Option B modifies VLAN 151’s private VLAN characteristic.
* Conclusion:Based on the requirement for isolation, none of the provided options are correct. However, if assuming a potential error in the question or options and needing to select the closest modification related to private VLAN types for VLAN 151, Option B is chosen tentatively, despite configuring
‘community’ instead of the required ‘isolated’.
References:AOS-CX Security Guide (Private VLAN configuration), Private VLAN concepts (Primary, Isolated, Community). This relates to the “Switching” (19%) and “Security” (10%) objectives.

NEW QUESTION 49
When trying to add a now access switch to the network, theswitch port at the aggregation switch is automatically disabled.
What needs to be done to fix this issue?

Disable spanning tree bpdu-tilter al the interface level.

Disable spanning tree root-guard at the interface level.

Disable spanning tree loop-guard at the interface level.

Disable spanning tree bpdu-guard at the interface level.

NEW QUESTION 50
AnOSPF router has teamed a path to an external network oy both an El and an E2 advertisement, both routes having the same path cost. Which path -will the router prefer?

The router will use both paths equally by means ofECMP

The router will prefer the E2 path.

Both routes will be suppressed until the path conflict has been resolved.

The router will prefer the E1 path.

NEW QUESTION 51
An HPE Aruba networking ClearPass server needs to be added in the configuration where Downloadable User Roles (DUR) are used.
What are the prerequisites for the AOS-CX Switch for DUR? (Choose two.)

The ClearPass server needs to be added as FQDN

A valid server certificate is required for the AOS-CX Switch.

A valid root certificate is required for the AOS-CX switch.

The ClearPass server can be added as IP or FQDN.

Empty role names need to be present on the switch

NEW QUESTION 52
What is the correct sequence of events that occurs when a user device connects to a network using Dynamic Segmentation?

NEW QUESTION 53
A customer wants to tunnel tagged traffic from the VoIP phones to a central location. Which UBT mode should you configure?

tunnel tagged

multi VLAN

local VLAN

VLAN extend

NEW QUESTION 54
Refer to the four numbered steps in the exhibit.

Which action is the first step in applying the role-to-role ACL on the traffic from mobile device M1 to role H2?

The edge switch acts as the intermediate node and transfers the Group Policy ID over static VXLAN to dynamic VXLAN tunnel and forwards the packet to switch A1.

The AP forwards the packet from M1 to gateway 1.

Switch A1 determines the destination role based on destination MAC or destination IP and enforces role-to-role ACLs.

Gateway 1 forwards the traffic over the static VXLAN tunnel to the edge switch; this packet carries the Group Policy ID corresponding to the role of M1.

[Feb-2026] HPE7-A06 Pre-Exam Practice Tests Exam Questions and Answers for Aruba Certified Professional – Campus Access Study Guide [Q38-Q54]

Leave a Reply Cancel reply

Related Posts

All Obstacles During HPE1-H03 Exam Preparation with HPE1-H03 Real Test Questions [Q90-Q106]

Get 100% Authentic HP HPE6-A69 Dumps with Correct Answers [Q33-Q56]

[Jun 10, 2022] Reliable HPE6-A70 Exam Tips Test Pdf Exam Material [Q72-Q89]