[Q679-Q694] Download Online VALID 200-301 Exam Dumps File Instantly [Oct 30, 2026]

Rate this post

Download Online VALID 200-301 Exam Dumps File Instantly[Oct 30, 2026]

200-301 Exam Dumps For Certification Exam Preparation

NO.679 Refer to the exhibit.

A network administrator assumes a task to complete the connectivity between PC A and the File Server.
Switch A and Switch B have been partially configured with VLAN 10, 11, 12, and 13. What is the next step in the configuration?

Add PC A to VLAN 10 and the File Server to VLAN 11 fa VLAN segmentation

Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation

Add a router on a stick between Switch A and Switch B allowing for Inter-VLAN routing.

Add PC A to the same subnet as the Fie Server allowing for intra-VLAN communication.

Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation. Switching features such as trunks and EtherChannels are controlled by negotiation mode, encapsulation, VLAN membership, and whether the selected protocol is Cisco proprietary or standards based. Cisco CCNA 200-301 v1.1 includes this topic under Network Access, so the answer must be validated against normal Cisco device behavior and the operational wording of the scenario. The key is not simply recognizing a familiar acronym; it is identifying what the feature does, where it is configured, and what result it produces. The incorrect options either disable negotiation, select the wrong negotiation protocol, or configure a mode that cannot form the requested link under the stated conditions. In a real network, selecting the wrong option would either leave the feature nonfunctional, create a forwarding or security gap, or send troubleshooting in the wrong direction. The selected answer is the only one that matches the stated requirement and the way Cisco switching, routing, services, security, wireless, or automation functions are expected to operate. This is why the verified answer remains the best technical choice for the question.

NO.680 Which two network actions occur within the data plane? (Choose two.)

Add or remove an 802.1Q trunking header.

Make a configuration change from an incoming NETCONF RPC.

Run routing protocols.

Match the destination MAC address to the MAC address table.

Reply to an incoming ICMP echo request.

NO.681

NO.682 Refer to the exhibit.

Which command must be executed for Gi1.1 on SW1 to become a trunk port if Gi1/1 on SW2 is configured in desirable or trunk mode?

switchport mode trunk

switchport mode dot1-tunnel

switchport mode dynamic auto

switchport mode dynamic desirable

NO.683 A network engineer is configuring an OSPFv2 neighbor adjacency Drag and drop the parameters from the left onto their required categories on the right. Not all parameters are used

NO.684 Refer to the exhibit.

What is represented by “R1” and “SW1” within the JSON output?

key

array

value

object

NO.685 Which spanning-tree enhancement avoids the learning and listening states and immediately places ports in the forwarding state?

BPDUfilter

PortFast

Backbonefast

BPDUguard

PortFast
Spanning Tree Portfast causes layer 2 switch interfaces to enter forwarding state immediately, bypassing the listening and learning states. It should be used on ports connected directly to end hosts like servers or workstations. Note: If portfast isn’t enabled, DHCP timeouts can occur while STP converges, causing more problems.

NO.686 Refer to the exhibit.

Shortly after SiteA was connected to SiteB over a new single-mode fiber path users at SiteA report intermittent connectivity issues with applications hosted at SiteB What is the cause of the intermittent connectivity issue?

Interface errors are incrementing

An incorrect SFP media type was used at SiteA

High usage is causing high latency

The sites were connected with the wrong cable type

NO.687 Drag and drop the WLAN components from the left onto the correct descriptions on the right.

NO.688 Refer to the exhibit.

NO.689 Drag and drop the device behaviors from the left onto the matching HSRP slate on the right.

Explanation

NO.690 Refer to the exhibit.

A network engineer must configure the link with these requirements:
* Consume as few IP addresses as possible.
* Leave at least two additional useable IP addresses for future growth.
Which set of configurations must be applied?

We have to configure the link which will need 2 IP addresses, 1 for each port on each Router. We also need 2 spare IPs for future growth, so overall we need 4 usable IP addresses. If we consider using the /30 (255.255.255.252) mask, it will give us 2^2 (=4) i.e., total 4 IPs and 2 usable IPs, which doesn’t fulfil the given requirements. So, we can consider using the next /29 (255.255.255.248) mask, which gives us 2^3 (=8) i.e., total 8 IP address and 6 usable IP addresses, which perfectly fulfil the given requirements.

NO.691 Refer to the exhibit. A network engineer must block access for all computers on VLAN 20 to the web server via HTTP. All other computers must be able to access the web server. Which configuration when applied to switch A accomplishes this task?

NO.692 Refer to the exhibit.

What does the host do when using the IPv4 Preferred function?

It continues to use a statically assigned IPv4 address

It forces the DNS server to provide the same IPv4 address at each renewal.

It requests the same IPv4 address when it renews its lease with the DHCP server.

It prefers a pool of addresses when renewing the IPv4 host IP address

NO.693 Refer to the exhibit.

Which configuration allows routers R14 and R86 to form an OSPFv2 adjacency while acting as a central point for exchanging OSPF information between routers?
A)

B)

C)

D)