NSE7_SDW-7.0 Actual Questions Answers PDF 100% Cover Real Exam Questions [Q31-Q47]

Rate this post

NSE7_SDW-7.0 Actual Questions Answers PDF 100% Cover Real Exam Questions

NSE7_SDW-7.0 Exam questions and answers

Fortinet NSE7_SDW-7.0 certification exam is a vendor-neutral certification, which means that it is recognized by a wide range of organizations and can be used to demonstrate expertise and knowledge in SD-WAN technologies. Fortinet NSE 7 – SD-WAN 7.0 certification is particularly valuable for network professionals who work in organizations that use Fortinet’s SD-WAN solution, as it demonstrates a high level of proficiency and expertise in managing and configuring this solution.

Fortinet NSE7_SDW-7.0 (Fortinet NSE 7 – SD-WAN 7.0) certification exam is a comprehensive exam that tests the skills and knowledge of networking professionals in the field of software-defined wide-area networks (SD-WAN). Fortinet NSE 7 – SD-WAN 7.0 certification validates the expertise and proficiency of individuals in designing, implementing, and managing SD-WAN solutions using Fortinet products and technologies.

Q31. Which diagnostic command can you use to show the member utilization statistics measured by performance SLAs for the last 10 minutes?

diagnose sys sdwan intf-sla-log

diagnose sys sdwan health-check

diagnose sys sdwan log

diagnose sys sdwan sla-log

SD-WAN 7.2 Study Guide page 321 You can view the stored member metrics by running the diagnose sys sdwan sla-log command. Note that you must include the name of the performance SLA followed by the member configuration index number. To display the SLA logs per interface, you run the diagnose sys sdwan intf-sla-log command.

Q32. Refer to the exhibit.

The exhibit shows the details of a session and the index numbers of some relevant interfaces on a FortiGate appliance that supports hardware offloading. Based on the information shown in the exhibits, which two statements about the session are true? (Choose two.)

The reply direction of the asymmetric traffic flows from port2 to port3.

The auxiliary session can be offloaded to hardware.

The original direction of the symmetric traffic flows from port3 to port2.

The main session cannot be offloaded to hardware.

Q33. In the default SD-WAN minimum configuration, which two statements are correct when traffic matches the default implicit SD-WAN rule? (Choose two )

Traffic has matched none of the FortiGate policy routes.

Matched traffic failed RPF and was caught by the rule.

The FIB lookup resolved interface was the SD-WAN interface.

An absolute SD-WAN rule was defined and matched traffic.

Q34. Which two statements about SD-WAN central management are true? (Choose two.)

The objects are saved in the ADOM common object database.

It does not support meta fields.

It uses templates to configure SD-WAN on managed devices.

It supports normalized interfaces for SD-WAN member configuration.

Normalized interfaces are not supported for SD-WAN templates. You can create multiple SD-WAN zones and add interface members to the SD-WAN zones. You must bind the interface members by name to physical interfaces or VPN interfaces.https://docs.fortinet.com/document/fortigate/7.0.0/sd-wan-new-features/794804/new-sd-wan-template-fmg

Q35. Which two statements about SD-WAN central management are true? (Choose two.)

The objects are saved in the ADOM common object database.

It does not support meta fields.

It uses templates to configure SD-WAN on managed devices.

It supports normalized interfaces for SD-WAN member configuration.

Explanation
Normalized interfaces are not supported for SD-WAN templates. You can create multiple SD-WAN zones and add interface members to the SD-WAN zones. You must bind the interface members by name to physical interfaces or VPN interfaces.https://docs.fortinet.com/document/fortigate/7.0.0/sd-wan-new-features/794804/new-sd-wan-template-

Q36. Which best describes the SD-WAN traffic shaping mode that bases itself on a percentage of available bandwidth?

Interface-based shaping mode

Reverse-policy shaping mode

Shared-policy shaping mode

Per-IP shaping mode

Interface-based shaping goes further, enabling traffic controls based on percentage of the interface bandwidth.

Q37. Which two statements are correct when traffic matches the implicit SD-WAN rule? (Choose two.)

The sdwan_service_id flag in the session information is 0.

All SD-WAN rules have the default setting enabled.

Traffic does not match any of the entries in the policy route table.

Traffic is load balanced using the algorithm set for the v4-ecmp-mode setting.

sdwan_service_id is 0 = match SD-WAN implicit rule, study guide 7.0 page 120, 7.2 page 149 SD-WAN rules internally are interpreted as a Policy route, so when the traffic doesn’t match with any policy route, it will be flowing by implict policy.

Q38. Which diagnostic command can you use to show the configured SD-WAN zones and their assigned members?

diagnose sys sdwan zone

diagnose sys sdwan service

diagnose sys sdwan member

diagnose sys sdwan interface

Q39. Refer to the exhibits.

Which two statements about the IPsec VPN configuration and the status of the IPsec VPN tunnel are true? (Choose two.)

FortiGate does not install IPsec static routes for remote protected networks in the routing table.

The phase 1 configuration supports the network-overlay setting.

FortiGate facilitated the negotiation of the T_INET_1_0_0 ADVPN shortcut over T_INET_1_0.

Dead peer detection is disabled.

Q40. Which two tasks are part of using central VPN management? (Choose two.)

You can configure full mesh, star, and dial-up VPN topologies.

You must enable VPN zones for SD-WAN deployments.

FortiManager installs VPN settings on both managed and external gateways.

You configure VPN communities to define common IPsec settings shared by all VPN gateways.

Q41. What is a benefit of using application steering in SD-WAN?

The traffic always skips the regular policy routes.

You steer traffic based on the detected application.

You do not need to enable SSL inspection.

You do not need to configure firewall policies that accept the SD-WAN traffic.

Q42. Refer to the exhibit, which shows the IPsec phase 1 configuration of a spoke.

What must you configure on the IPsec phase 1 configuration for ADVPN to work with SD-WAN?

You must set ike-version to 1.

You must enable net-device.

You must enable auto-discovery-sender.

You must disable idle-timeout.

Q43. Which two interfaces are considered overlay links? (Choose two.)

LAG

IPsec

Physical

GRE

Q44. Refer to the exhibit.

The device exchanges routes using IBGP.
Which two statements are correct about the IBGP configuration and routing information on the device? (Choose two.)

Each BGP route is three hops away from the destination.

ibgp-multipath is disabled.

additional-path is enabled.

You can run the get router info routing-table database command to display the additional paths.

Q45. In a hub-and-spoke topology, what are two advantages of enabling ADVPN on the IPsec overlays? (Choose two.)

It provides the benefits of a full-mesh topology in a hub-and-spoke network.

It provides direct connectivity between spokes by creating shortcuts.

It enables spokes to bypass the hub during shortcut negotiation.

It enables spokes to establish shortcuts to third-party gateways.

Q46. Refer to the exhibits.
Exhibit A –

Exhibit B –

Exhibit A shows the SD-WAN performance SLA and exhibit B shows the SD-WAN member status, the routing table, and the performance SLA status.
If port2 is detected dead by FortiGate, what is the expected behavior?

Port2 becomes alive after three successful probes are detected.

FortiGate removes all static routes for port2.

The administrator manually restores the static routes for port2, if port2 becomes alive.

Host 8.8.8.8 is reachable through port1 and port2.

This is due to Update static route is enable which removes the static route entry referencing the interface if the interface is dead

Q47. What is the route-tag setting in an SD-WAN rule used for?

To indicate the routes for health check probes.

To indicate the destination of a rule based on learned BGP prefixes.

To indicate the routes that can be used for routing SD-WAN traffic.

To indicate the members that can be used to route SD-WAN traffic.

Loading …

Real4dumps NSE7_SDW-7.0 Exam Practice Test Questions: https://www.real4dumps.com/NSE7_SDW-7.0_examcollection.html

NSE7_SDW-7.0 Actual Questions Answers PDF 100% Cover Real Exam Questions [Q31-Q47]

Leave a Reply Cancel reply

Related Posts

[Jun-2023] Exam Sure Pass Fortinet Certification with NSE7_PBC-6.4 exam questions [Q14-Q30]

Latest Fortinet NSE6_FNC-9.1 PDF and Dumps (2024) Free Exam Questions Answers [Q17-Q31]

[Jul 23, 2022] NSE7_PBC-6.4 Exam Brain Dumps – Study Notes and Theory [Q12-Q27]